Oil and gas refinery at night with illuminated processing stacks and pipeworkRefinery at night with illuminated stacks

The subsea tree is the primary wellhead production control equipment installed on a subsea well. It is the interface between the wellbore — the drilled and cased hole that penetrates the reservoir — and the subsea production system: flowlines, umbilicals, manifolds, and risers that transport production to the surface. In function, a subsea tree performs the same role as a conventional surface wellhead Christmas tree: providing the valves, chokes, and instrumentation to control production flow, shut in the well in emergencies, and enable well intervention. In engineering, a subsea tree is dramatically more complex than its surface equivalent — designed to operate reliably without human access for periods measured in years, in temperatures approaching freezing, under pressures of hundreds or even thousands of bar, and with control signals and hydraulic power transmitted from the surface via umbilical systems running tens of kilometres across the seabed. The evolution of subsea tree technology over the past four decades has been one of the defining engineering achievements of the offshore oil and gas industry.

Vertical vs Horizontal Subsea Trees: The Fundamental Design Choice

Subsea trees come in two fundamental configurations: vertical tree (VT) and horizontal tree (HT). The choice between them has significant implications for wellbore access, completion procedures, well intervention, and the overall well architecture. Both designs are in widespread use globally, and selection criteria vary by operator preference, field characteristics, and the planned intervention strategy.

A vertical tree (sometimes called a conventional tree) is installed on top of the wellhead housing after the well is drilled and cased, but before the production tubing is run. The production tubing is then run through the tree and landed in the production packer below. The tree valves — master valve, swab valve, production wing valve, annulus wing valve — are oriented vertically in the flow path, with the tree spool supporting the tubing hanger. Vertical trees allow relatively easy well access for intervention operations: once the tree is depressurised and the wellbore barrier is established, the Christmas tree can be removed and intervention tools run directly into the well through the wellhead.

A horizontal tree (HT) inverts the conventional architecture. The tubing hanger is landed in the wellhead housing (rather than in the tree), and the tree is then installed over the tubing hanger. The tree valves are arranged horizontally in the production bore — the flow path exits through the side of the tree rather than vertically — which is the distinctive feature of the horizontal tree design. Horizontal trees allow the use of large-bore internal tree caps (ITCs) to provide wellbore isolation, enabling well intervention through the tree without removal. HTs also have a smaller footprint (lower installed height) than vertical trees, which can be important for riser spacing on congested subsea manifolds. TotalEnergies, Shell, and Equinor have been major proponents of horizontal tree technology for deepwater applications.

Deepwater Tree Specifications: Pressure, Temperature, and Materials

Deepwater subsea trees are manufactured to stringent API 17D (Design and Operation of Subsea Production Systems — Subsea Wellhead and Tree Equipment) specifications, with class society (DNV, Lloyd’s Register) verification of the design, manufacturing, and testing processes. The pressure ratings required for deepwater HPHT wells push to the limits of current technology: trees rated to 15,000 psi (1,034 bar) working pressure are now standard for HPHT applications, and the industry is developing 20,000 psi (1,379 bar) rated systems for the most extreme reservoir conditions in the Gulf of Mexico Paleogene and similar HPHT plays.

The material selection for subsea trees — bodies, bonnets, valves, seals, and connection hubs — must address the combined challenge of high pressure, low temperature seabed conditions, corrosive production fluids (H2S, CO2, chlorides), and the requirement for 25-year component life without maintenance access. The primary tree body is typically manufactured from low-alloy steel with appropriate toughness at low temperature — ASTM A694 F65 or higher-strength grades — with corrosion-resistant alloy (CRA) internal cladding in the flow bore for sour service applications. Valve gate and seat materials are typically Inconel 625, 316L stainless steel, or specialty alloys optimised for the specific wellbore fluid composition. Elastomeric seals (nitrile, hydrogenated nitrile, FFKM) must be qualified for the production fluid chemistry, temperature cycling, and pressure cycles expected over the field life.

Tree Manifold and Cluster Architecture

Most modern deepwater subsea developments use a manifold-based gathering architecture: multiple subsea trees (typically 4-8 per manifold) are connected by short flowlines (jumpers) to a central subsea manifold, which gathers production from all connected wells and delivers it via a single export flowline to the FPSO or platform. This architecture reduces the number of risers and long flowlines required — a significant cost and complexity saving compared to connecting each well directly to the FPSO.

The subsea manifold itself is a substantial piece of equipment — a large, diver-accessible or ROV-maintained structure incorporating multiple wellhead connection points, production and test headers, pressure-balanced pigging connections, and a control and monitoring system connected to the field umbilical. Manifold designs range from relatively simple two-slot template manifolds to large multi-slot structures capable of connecting 12 or more wells, with integrated commingling, pressure boosting, and chemical injection capabilities.

Tree Installation: Running Tools and Installation Vessels

Subsea tree installation requires specialist equipment and vessels. Trees are typically installed from drill ships or semi-submersible drilling rigs using purpose-designed running tools, which engage the tree structure and provide the torque and force required to land and lock the tree onto the wellhead connector. The wellhead connector — a hydraulically or mechanically actuated clamp connector that locks the tree onto the wellhead housing — must achieve metal-to-metal sealing under the combined loads of tree weight, wellbore pressure, and environmental forces.

For deepwater installations (beyond ROV intervention reach for tree installation by crane vessel), the tree is run on the drill string or a dedicated running tool string through the rig’s moonpool, with the tree landing and lockdown operations controlled from the rig’s subsea control system. Hydraulic flying leads and electrical jumpers — temporary connections made by ROV between the tree and the subsea umbilical termination assembly — connect the tree to the production control system before production testing and startup.

All-electric subsea trees — where hydraulic actuation is replaced entirely by electric motor actuators on tree valves — represent a growing trend in the industry. All-electric trees eliminate the need for hydraulic fluid supply via umbilical (simplifying the umbilical architecture and eliminating the risk of hydraulic fluid spills), allow faster and more precise valve control, and enable comprehensive diagnostic monitoring of valve status. Aker Solutions, Baker Hughes, and TechnipFMC are all developing all-electric subsea tree systems, with early deployments in the North Sea and Gulf of Mexico demonstrating the concept’s viability.

Major Suppliers: TechnipFMC, Baker Hughes, and Aker Solutions

The subsea tree market is dominated by three suppliers: TechnipFMC (formed by the merger of Technip and FMC Technologies), Baker Hughes (following GE Oil & Gas’s merger into Baker Hughes), and Aker Solutions (the Norwegian subsea equipment company). These three companies together supply the vast majority of deepwater subsea trees globally, competing on technology, price, delivery timescale, and local content in their target markets.

Each major supplier has proprietary tree designs: TechnipFMC’s NEMO and compact tree designs, Baker Hughes’s DeepVision horizontal tree, and Aker Solutions’ standardised tree platforms. The trend toward standardisation — with operators specifying subsea equipment to standard designs that are pre-qualified and pre-engineered rather than bespoke, to reduce lead times and costs — has been a significant market development, supported by the JIP33 (Joint Industry Project 33) initiative at IOGP that has produced standardised specifications for subsea trees and other equipment categories.

The subsea tree market is expected to see steady growth through the late 2020s, driven by the large pipeline of deepwater FPSO developments in Guyana, Brazil, West Africa, and the Gulf of Mexico. Each new FPSO development requires multiple subsea trees — typically 8-24 trees per FPSO from a combination of production wells and potential injector wells — sustaining healthy order volumes for the three dominant suppliers.